![]() Connect your fiber and press the Test button. ![]() Detects live optical signals before it begins testing.Find potential sources of high bit error rates caused by reflectance from dirty or poor connections.Locate severe bends, high-loss splices, breaks and dirty connectors in multimode fiber.Measure up to 4,921 feet (1,500 metres) of fiber in seconds Multimode Fiber Distance and Fault Locator Looks for a signal every 3 seconds after the first detec-tion. If no fiber is attached or if the connector is dirty, the troubleshooter displays 0 m or 0 ft.ĭetects optical signals from 600 nm to 1050 nm and shows ACTIVE LINE if a signal is there. 35 dB default threshold (User selectable: -20 dB to -45 dB in 5 dB increments)Ġ.70 dB default threshold (user-configurable from 0.5 dB to 6.1 dB in 0.2 dB increments) ![]() Removable/cleanable SC adapter, UPC polish ± (1 m + 0.1 % x length) for reflective incidents 1 ± (3 m + 0.1 % x length) for non-reflective incidents 2 A certifying OTDR is recommended to troubleshoot these situations. Find problems quickly.Operating relative humidity (without condensation)ĩ5% (10✬ to 35✬) 75% (35✬ to 40✬) uncontrolled 11 dBĭistance accuracy (0 m to 1500 m or 0 ft to 4921 ft) Due to testing variables, Fiber QuickMap occasionally cannot see connections The maximum link loss prior to the incident is <7 dB. ± (1 m + 0.1 % x length) for reflective incidents1 ± (3 m + 0.1 % x length) for non-reflective incidents 2ġm after the bulkhead connector when the bulkhead reflectance is 3 m after an incident when the incident reflectance is 10 m after the bulkhead connector or any prior incident when the bulkhead reflectance is <-35 dB and the reflectance of any prior incident is <-35 dB. Operating relative humidity (without condensation)ĩ5% (10✬ to 35✬) 75% (35✬ to 40✬) uncontrolled 11 dBĭistance accuracy (0 m to 1500 m or 0 ft to 4921 ft) When and Where to Use Fiber OneShot PRO and Fiber QuickMapįiber OneShot PRO provides immediate and in-depth visibility into a singlemode fiber cable (below).įiber QuickMap operates the same, except on multimode fiber up to 1,500 meters / 4,921 feet.įluke Networks Fiber QuickMap Series Specifications Rugged construction vibration and drop tested to 1 meter.Long battery life, 1,500 tests (typical) from 2 AA alkaline batteries.Optional LC, ST and FT interchangeable adapters are available.Key information visible on a large display power loss in db and distance in meters or feet.Measure and locate high loss connections and breaksįeatures common to both Fiber OneShot PRO and Fiber QuickMap.Locate severe bends, high-loss splices, breaks and dirty connectors in singlemode fiber Measure and locate high-loss splicesįind potential sources of high bit error rates caused by reflectance from dirty or poor connections Measure up to 4,921 feet (1,500 metres) of fiber in seconds Locate the end of a fiber Backlighted display turns off automaticallyĩ/125µm and 62.5/125 µm 850 nm output wavelength Change the Index of Refraction (IOR) to improve fiber length accuracy /PRNewswire/ - Fluke Networks today announced the release of Fiber QuickMap, a new fiber troubleshooter for enterprise network technicians which provides.Six-second test time-no more blind troubleshooting that can waste hours Locate severe bends, high-loss splices, breaks and dirty connectors in singlemode fiber.NOTE: Fluke Network lead times can vary due to component and supply issues.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |